ᐅ How do I repair a broken Ikea Metod cabinet door hinge?

Hello everyone,

I recently discovered that one of the door hinges on my Ikea Metod kitchen cabinet has broken. Specifically, it is the inner hinge that suddenly lost its support completely when opening the door and now does not hold properly. I suspect that the small plastic part inside the hinge housing has cracked or fallen out.

My question is, what is the best way to repair this broken Metod door hinge? Should I replace the entire hinge, or are there spare parts available, such as the plastic component, that can be replaced individually? If anyone has experience with this issue and repair solutions, I would appreciate concrete advice—how to safely remove the hinge, which tools are needed, and whether it can be repaired by oneself without removing the entire door.

Thank you in advance for your help!

gajelo schrieb:
I recently noticed that one of the door hinges on my Ikea Metod kitchen cabinet has broken.

Oh dear, that can really spoil the mood of any kitchen enthusiast! Ikea Metod hinges are usually modular and, fortunately, not too expensive to replace entirely. When the plastic parts break, it’s often best to replace the whole hinge—getting individual replacement parts for the small plastic components is usually difficult since manufacturers aren’t very generous with those.

What you can do is carefully unscrew the hinge (a Phillips screwdriver works best) and replace it entirely. You can find replacement hinges fairly cheaply at hardware stores or Ikea. Taking the door off first makes the process easier.

A quick tip: when reinstalling, make sure the screws are tightened securely and the hinges are properly aligned, otherwise the door will hang unevenly. Don’t worry, it’s not rocket science, even if you’d rather watch than actually do the repair!

gajelo schrieb:
Should I replace the entire hinge, or are there spare parts, like the plastic piece, that can be replaced individually?

Unfortunately, you have to replace the entire hinge. Plastic parts are not available separately.

Remove the door from its hinges, unscrew the hinge, fit the new hinge, then adjust the door.

I would like to add a more detailed look at the technical side to this thread. Ikea Metod hinges are usually the common screw-on hinges with plastic dampening in some versions. If the hinge breaks internally, it often affects either the spring mechanism or the supporting plastic component.

Regarding repairs: There are no official replacement parts available for the plastic interior. All repair attempts using glue or similar methods are generally only short-term solutions and can impair functionality.

Practically and economically, a complete replacement of the hinge is therefore advisable. Removal is done by unscrewing the two screws on the hinge and detaching the door from the hinge plates.

The tools required are a Phillips screwdriver (PH2) and possibly a small flathead screwdriver for clamping screws. Then, the new hinge can be screwed on again according to the mounting grid.

The door is then adjusted using the adjustment screws on the hinge to ensure optimal closing and opening angles. This is a relatively simple task if done carefully.

hauklo schrieb:
All repair attempts with glue or similar substances are usually only short-term solutions

This is an important point. Some time ago, I tried to fix a broken hinge with superglue myself, but the door quickly became slightly loose again and rattled as a result.

I know it’s frustrating to repair something like this, especially if you don’t have deep technical experience. However, it really helps to replace the entire hinge. The first time you do it might take a little while, but after that the door will sit securely again.

I wish you good luck with it, and if you’re unsure, feel free to reach out again! Sometimes it also makes sense to proceed patiently and try the steps one at a time.

gajelo schrieb:
I suspect that the small plastic part inside the hinge housing is cracked or missing.

That is very likely the core of the problem. These small plastic components are responsible for snapping in place and holding the spring tension, and they break under heavy use or material fatigue.

To remove the door, lift it slightly and carefully pull it off – usually, the top hinge is designed this way. Then, unscrew the damaged hinge using a Phillips screwdriver. I recommend using a new hinge for reinstallation, as used hinges often already show slight signs of wear.

One more tip: work on a padded surface to avoid scratches, and use a small flashlight if the workspace is dim.

If you have any further questions, feel free to ask!