ᐅ Modernist Concrete Villa with Cavity Wall Insulation – Experiences
Created on: 11 Sep 2018 07:32
R
rick2018
Hello everyone,
I just wanted to briefly introduce myself and say thank you.
For about a year and a half, I have been a silent reader here to gather inspiration and especially to gain more knowledge about construction technology.
Now a bit about me:
After more than a year of searching for a plot of land, I was able to purchase one from a developer who couldn’t move forward quickly with his plans.
So we found our dream plot (good location, 2500 m² (0.62 acres), slight slope, underground private spring that we have to preserve and are allowed to use).
There was an old house on the property, which we have since demolished.
There is no zoning plan, so §34 applies. During an initial informal inquiry at the building authority, almost everything we planned was rejected.
So we submitted an official preliminary building inquiry, involved the right people, and had lengthy discussions. In the end, we received a positive decision.
Therefore, there is nothing standing in the way of the building permit. The building permit should be granted within the next few weeks as there are no changes from the preliminary inquiry.
My wife (37) and I (36) want to build a Bauhaus-style villa in southern Baden-Württemberg.
It will be constructed from concrete (with core insulation) or in combination with insulated precast elements.
A lot of glass (full-glass system), textile shading, KNX, fast network both wired and wireless, strong mechanical ventilation with additional cooling coils, stainless steel pool, large cistern, and more.
The electrical planning must be 100% spot on since it’s almost impossible to make changes afterward.
Since I am friends with an architect from a larger firm, it was clear which route we would take. Such a house can basically only be realized with an architect.
I also personally know the electrician and KNX system integrator, as well as the owners and work approach of the heating, plumbing, and ventilation companies involved.
Some trades have already been contracted, and part of the equipment has already been ordered.
I’m really looking forward to getting started and to the final result. The goal is to move in by the end of 2019.
Once again, many thanks for the information I have received from you so far.
If you have any questions, just let me know.
Attached is the design, though not the final version. There have been a few minor changes.
Greetings from Swabia
I just wanted to briefly introduce myself and say thank you.
For about a year and a half, I have been a silent reader here to gather inspiration and especially to gain more knowledge about construction technology.
Now a bit about me:
After more than a year of searching for a plot of land, I was able to purchase one from a developer who couldn’t move forward quickly with his plans.
So we found our dream plot (good location, 2500 m² (0.62 acres), slight slope, underground private spring that we have to preserve and are allowed to use).
There was an old house on the property, which we have since demolished.
There is no zoning plan, so §34 applies. During an initial informal inquiry at the building authority, almost everything we planned was rejected.
So we submitted an official preliminary building inquiry, involved the right people, and had lengthy discussions. In the end, we received a positive decision.
Therefore, there is nothing standing in the way of the building permit. The building permit should be granted within the next few weeks as there are no changes from the preliminary inquiry.
My wife (37) and I (36) want to build a Bauhaus-style villa in southern Baden-Württemberg.
It will be constructed from concrete (with core insulation) or in combination with insulated precast elements.
A lot of glass (full-glass system), textile shading, KNX, fast network both wired and wireless, strong mechanical ventilation with additional cooling coils, stainless steel pool, large cistern, and more.
The electrical planning must be 100% spot on since it’s almost impossible to make changes afterward.
Since I am friends with an architect from a larger firm, it was clear which route we would take. Such a house can basically only be realized with an architect.
I also personally know the electrician and KNX system integrator, as well as the owners and work approach of the heating, plumbing, and ventilation companies involved.
Some trades have already been contracted, and part of the equipment has already been ordered.
I’m really looking forward to getting started and to the final result. The goal is to move in by the end of 2019.
Once again, many thanks for the information I have received from you so far.
If you have any questions, just let me know.
Attached is the design, though not the final version. There have been a few minor changes.
Greetings from Swabia
S
Seven198411 May 2021 08:57rick2018 schrieb:
@stekna We have an infinity pool. Therefore, a sliding enclosure was never really an option. I don’t like the look either, and you also need a place to slide it to. However, it does make sense to have a cover on the water.
Our advantage is that we hardly get any biomass entering the pool. I simply open the (floating) cover. A few leaves may fall into the pool, but I either remove them while swimming or the robot takes care of it.
If there’s a lot of debris on the cover, you can also remove it with a leaf blower or garden hose (the leaves then fall over the edge).
The polycarbonate covers are easy to clean with a pressure washer or a brush. Once a year is enough. It’s important that they are always kept in the water or protected from sunlight.
Ours is a polycarbonate solar cover that rolls up into a hidden underwater pouch. So nothing is visible.
I would definitely choose this again. Even covers that are several years old still looked great.
More problematic and prone to damage are the cheaper PVC covers.
With minimal care, you will enjoy a polycarbonate cover for many years. The rest of the pool usually requires more maintenance (even if most of it is automated).Hello Rick, could you please share more details about your cover? Do you possibly have pictures? We are starting work on our outdoor area in the next 2 to 3 weeks, and by then I need the final dimensions of my pool (we are also planning an infinity pool - as I mentioned in my thread, but under different commercial circumstances ;-) ). In my opinion, this is closely related to the cover. Many thanks!bortel schrieb:
I think these might fit... sorry @rick2018
Engelshove Bau GmbH Wow. From what I see, I would probably move into any of their houses... That’s exactly how I wanted to build, but unfortunately, it wasn’t financially possible 😀
Why apologize?
At least based on the website, it seems like a good suggestion. The cubic style definitely fits.
From the pictures, you can see they mostly work with bricks rather than concrete. I can't really judge to what extent "smart" technologies or similar options are within their capabilities.
I believe every suggestion helps @k-man2021 move forward.
At least based on the website, it seems like a good suggestion. The cubic style definitely fits.
From the pictures, you can see they mostly work with bricks rather than concrete. I can't really judge to what extent "smart" technologies or similar options are within their capabilities.
I believe every suggestion helps @k-man2021 move forward.
@Seven1984 What exactly do you want to know?
Basically, there are floating covers made of PVC or polycarbonate.
Polycarbonate is much more expensive but also more durable and robust.
Our cover also has an anti-algae and solar function. Silver on top and black underneath.
You can check out BAC-Poolsystems or Waterbeck GmbH. They explain it well there.
The motor and cover are installed in a niche in the pool. In front of it is a removable wall. On top, there is a slot where the cover comes out.
On the side of the overflow channel, special pendulum sliders are attached to the cover. These fold out as soon as the cover floats and extend a few cm (inches) into the water. This prevents the cover from floating over the edge. However, this is very unlikely anyway since it is a robust roller cover.
During installation:
Basically, there are floating covers made of PVC or polycarbonate.
Polycarbonate is much more expensive but also more durable and robust.
Our cover also has an anti-algae and solar function. Silver on top and black underneath.
You can check out BAC-Poolsystems or Waterbeck GmbH. They explain it well there.
The motor and cover are installed in a niche in the pool. In front of it is a removable wall. On top, there is a slot where the cover comes out.
On the side of the overflow channel, special pendulum sliders are attached to the cover. These fold out as soon as the cover floats and extend a few cm (inches) into the water. This prevents the cover from floating over the edge. However, this is very unlikely anyway since it is a robust roller cover.
During installation: